Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
JH
Good solution for desktop nearfields
I have a pair of floor stands behind my desk with Yamaha HS8s on them. That´s all good, but I also wanted a second set of smaller monitors for A/B comparison when mixing. These are ideal for this, and sit on either side of my screen without taking up much desk estate. The clamps are ingenious for this. They give you flexibility in speaker placement, and these are sturdy and well-made. The rubber mat is a nice touch to angle the speakers slightly without fear of them sliding off. Highly recommended!
0
0
Reportar a crítica
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
B
Decent monitor stands
I have clamped these to the sides of my desk and they do the job. They are slightly wobbly front to back but nothing problematic.
0
1
Reportar a crítica
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
St
Using with KRK Rokit 5 G4
It's been a month, all rock solied, they fir perfectly and don't cost too much. Definitely recommend
1
0
Reportar a crítica
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
L
Saves up space on your desk
Excellent build quality with easy height/angle adjustments. I use them to free up some space on my desk. They hold a pair of PreSonus Eris 3.5 speakers, and they are stable on the stands. I am confident bigger speakers would also easily fit as there is a bit of space on the sides.
0
0
Reportar a crítica
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
A
High quality but perhaps lacks fine adjustment
I have Kali IN-6 on them, the left speaker on the stand has maybe 1 degree sideways tilt which I can't correct, but it's not that visible. The right speaker on the stand however has a couple of more degrees of an angle and if I flip the top of the stand, then it's even worse.
It would be nice if it was possible to tilt it a bit sideways, but I don't see an option how except maybe with a shim between top board and post, so to say, but that's too much work for small angle.
So aesthetically it's 4/5, overall it's great. I've had wall mounted ones before, but now with standing desk this is much better.
It would be nice if it was possible to tilt it a bit sideways, but I don't see an option how except maybe with a shim between top board and post, so to say, but that's too much work for small angle.
So aesthetically it's 4/5, overall it's great. I've had wall mounted ones before, but now with standing desk this is much better.
0
0
Reportar a crítica
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
D
Not the most intuitive to set up, but worth it 100%
These monitor speaker clamps are very high quality once set up. That said, I do have a few tiny critiques. The first issue is that setting them up is not the most intuitive, as the screws are tightened by turning to the left (against the righty tighty lefty loosey paradigm). Also the Allan key is a bit too long to screw in cylinder stand itself into the clamp, so you need to first use your fingers to gently get the screw in before using the Allan key to finish the job. Other than that 5 minutes of kerfuffle, these stands are really really good.
1
0
Reportar a crítica
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
S
Decent stands for budget
Stands look nice and neat however quality of screws are not the best and the speaker leans a bit to one side.
0
0
Reportar a crítica
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
c
ideal sturdy vibration free desk stand for my old auratones
i was looking for stands for my old auratones, with following requirements:
a) vibration free and solid when clamped to the edge of my work desk
b) thick, ruberry, non slip surface
c) ability to change front/back angle so i slightly elevate the projection
d) slim but strong vertical axis - so it doesn't present too big acoustic obstacle for my midfields, which are a meter behind and ider positioned (scm50).
was sceptical about Roadworx, somewhat perceiving it as low end-ish company, but their stand has provided all of the above.
very, very satisfied. to a point that it made me look more seriously at their other products of interest.
a) vibration free and solid when clamped to the edge of my work desk
b) thick, ruberry, non slip surface
c) ability to change front/back angle so i slightly elevate the projection
d) slim but strong vertical axis - so it doesn't present too big acoustic obstacle for my midfields, which are a meter behind and ider positioned (scm50).
was sceptical about Roadworx, somewhat perceiving it as low end-ish company, but their stand has provided all of the above.
very, very satisfied. to a point that it made me look more seriously at their other products of interest.
0
0
Reportar a crítica
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
J
Sturdy
Solid balance for Adam A7!
0
0
Reportar a crítica
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
A
Very Sturdy. Highly recommended
I have my Edifier R1850BT on these and they are rock solid. I move my desk up/down everyday and they hold very well.. no moving around. They bring the monitors up to ear level and are very adjustable in angles and rotation.
0
0
Reportar a crítica